Home > Products > Production Line Solutions > Body Wash Production Line
Body Wash Production Line
  • Body Wash Production LineBody Wash Production Line
  • Body Wash Production LineBody Wash Production Line
  • Body Wash Production LineBody Wash Production Line

Body Wash Production Line

    The Kinding shower gel production line is designed to meet the production needs of shower gels, shower gels and body scrub products and the core equipment includes a high-speed shear emulsification mixing system, a vacuum degassing tank and an automatic filling line. The surface active agent content in the shower gel formula is relatively high, and a large amount of foam is generated during the stirring process , and the Kinding vacuum emulsification tank can efficiently remove bubbles and prevent oxidation. The forced circulation design of the circulating emulsification mixing tank ensures that the high-viscosity shower gel base material circulates without dead corners in the tank, avoiding uneven emulsification caused by the cutting blind zone. You can choose flexible configurations ranging from a single emulsification tank to a complete automated production line when purchasing Kinding shower gel production equipment. Please contact us for process adaptation suggestions and equipment selection lists for the shower gel production line.

    Send Inquiry

    Product Description

    If you are planning to produce body wash or are looking for ways to increase production capacity and quality, this introduction will provide you with a clear and practical reference. The production of body wash is quite different from the production of ordinary lotions. It pays more attention to batch processing capabilities, the transparency of the liquid, the stability of the foam, and the retention of fragrance. A good body wash production line is not just a simple combination of a few pieces of equipment, but a full-process collaboration from water treatment to filling and sealing.

    First, let's start from the source. In a bottle of body wash, water is the component with the highest content. The quality of the water directly affects the transparency, smell, and stability of the product. Our production line is equipped with a water treatment system that softens the tap water and removes ions, obtaining pure process water.

    This water is then transported to the water phase preparation tank, where it is heated, mixed with water-soluble raw materials such as glycerin, moisturizers, and emulsifiers to form a transparent and uniform water phase and at the same time, the oil phase preparation tank is processing oil-soluble components such as oils, fatty acids, and emulsifiers. The advantage of this approach is that each raw material can be pre-dissolved under the most suitable conditions, avoiding the appearance of particles or incomplete dissolution during subsequent mixing.

    The most crucial step is emulsification. The texture of body wash, from the refreshing transparent liquid to the thick pearl-like cream, depends on this step. Our core equipment is a vacuum homogenization emulsifier. You can imagine its function as a powerful and high-speed mixer combined with a vacuum cover. The material is sucked into the rotating rotor inside the tank and passes through the narrow stator gap, subjected to intense shearing and impact, where oil and water are thoroughly broken into extremely fine particles, forming a uniform and stable state.

    The vacuum environment ensures that no air is mixed during the entire process, resulting in a crystal clear body wash without bubbles. For those high-viscosity moisturizing body washes, our emulsifier also comes with an anchor-type scraper mixer. It rotates closely against the tank wall, scraping off the sticky materials adhering to the wall, and sending them to the emulsification head for recycling, leaving no dead corners.

    After emulsification, the material temperature is still very high, especially during the hot mixing process, with temperatures often around 70-80 degrees Celsius. At this point, fragrance cannot be added immediately because high temperatures will cause the fragrance to evaporate and damage some active ingredients. Therefore, we have designed a rapid cooling system. The material is cooled through a jacketed cooling or external circulating cooler, reducing the temperature to below 40 degrees Celsius within a few minutes.

    The cooling speed is very important. Rapid cooling can reduce energy consumption and make the liquid state more stable, avoiding coagulation or stratification. After cooling, fragrance, pearl pigments, pigments, and functional additives can be added. This step requires very gentle stirring because excessive shear force will damage the fragrance molecules of the fragrance and break the pearl crystal sheets. Our low-speed variable-frequency stirrer can precisely control the speed, allowing these sensitive materials to slowly and evenly blend into the entire system.

    Then comes the static and filtration stage. The freshly made body wash may contain a small amount of undissolved impurities or bubbles. The static buffer tank we have configured allows the material to rest in a constant temperature and light-protected environment for a period of time, completing the final expansion and defoaming. Afterwards, the material passes through a stainless steel filter and is transported to the high-level storage tank in the filling workshop by a sanitary-level conveying pump.

    The filling process is also an important part affecting the quality of the finished product and production capacity. We offer various specifications of filling machines, ranging from manual or semi-automatic equipment suitable for small bottles to fully automatic multi-head filling lines suitable for large-scale production. The filling machines use piston or flow meter quantification, with high precision and no situations of over-filling or under-filling. Combined with automatic cap-laying machines, labeling machines, and inkjet printers, the entire filling and packaging line can be completed seamlessly.

    When it comes to daily maintenance, we have specially designed an online CIP cleaning system. When producing different scents of body wash, just press a few buttons and the system will automatically inject the cleaning solution, which will circulate in the tank and pipeline for cleaning, and then be rinsed with clean water. The entire process does not require manual disassembly or assembly.

    Whether you are a newly established factory or a mature enterprise with a certain scale, we can customize an appropriate body wash production line solution for you based on your production volume, product type and factory space. From equipment selection, layout planning to installation and commissioning, as well as personnel training, we will accompany you throughout the process.

    Body Wash Production LineBody Wash Production LineBody Wash Production Line

    Related Category
    Send Inquiry
    Please Feel free to give your inquiry in the form below. We will reply you in 24 hours.
    X
    We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
    Reject Accept